QT front seal replacement (in memory of Joe Sego)
Date: Mon, 20 Jan 1997 01:09:55 -0500
From: Joe Sego
Subject: QT Front Seal Repl.
BW Model 1339 Quadra-Trac Front Seal Replacement
A while back I noticed a drip from my 1979 Cherokee Chief's
transfer case. Upon further inspection I determined it was Dextron
tranny fluid and NOT the Jeep QT fluid. The seals between the TH400
auto transmission and the Quadra-trac unit were bad. Tranny fluid was
entering the transfer case.....NOT GOOD!
There are two seals in the transfer case, there are NO seals on rear of
the TH400 transmission. Actually this is a blessing, I'd much rather
pull the transfer case than the Th400. I ordered the new seals from a
Jeep dealer. They were $3.39 each, not bad huh? *note* some model
years require a gasket between tranny and transfer case. The 79 Cherokee
does not.
PULLING The Borg Warner 1339 Quadra-Trac Case
1. Jack up vehicle and use jack stands.
2. Mark front and rear drive shafts so they can be installed in same position.
3. Remove front and rear drive shafts
4. If so equipped unhook low range linkage and low range unit
5. Mark and unhook the two vacuum lines to Emergency Drive popet valve on
top of transfer case.
6. Unplug wire to Emergency Drive light indicator
7. Remove two 3/8" bolts from transfer case to transmission (on rear of case)
8. Remove two 3/8" bolts from tranny to transfer case (front of case)
9. CAREFULLY slide transfer case rearward, approx. 4" until it disengages
from tranny rear shaft. THE CASE WEIGHS ABOUT 75 POUNDS !!
I'd use a tranny jack if available.
10. Once it's on the floor, clean it up and remove the two front seals.
Pay particular attention to the fact that both seals are back to back
and turned opposite of each other. Install the new ones in same
manner! They drive right in with the help of a small piece of pipe and
a hammer.
REASSEMBLY
Please note you will need two 3/8" bolts approx 5" long with the head cut off.
These are screwed in the holes where the two rear bolts were removed. These
bolts act as a guide for the transfer case, installing the case without
these bolts will almost always damage the new seals. Once the case is up
against the tranny the guide bolts can be removed and regular bolts installed.
The rest of the assembly is the reverse of the above. I would go ahead and
change the transfer case fluid.
It takes two quarts and you need to buy it at Jeep. $9.95 per quart. Yes,
it is a special fluid for the clutches in the Quadra-Trac unit. Regular oil
will NOT work.
joe sego (RIP)
superdawg
SJ 1962 - 1991
-- tech / repair tips
SJ rigs - photos
the 1996 snowstorm
john's '83 Long bed J10
|
since September 24, 1998.
|
These copyrighted pictures
are available for purchase,
contact john at this domain.
|
books, toys, parts, etc.
for sale here, on CL, or ebay
shop here, support this site:
|
WJ 1999-2004
WJ rigs
XJ 1984-2001
XJ tech - repair tips
XJ rigs - photos
|
Search Tool
|
KJ CRD 2005-2006
WILLYS /
JEEPS
|
AMSOIL
call 1-800-956-5695,
CUSTOMER NUMBER is 283461
FSJ Filters
XJ Filters
|
Nuts-Bolts-Wrench specs
DIESELS
Jetta TDI's
Mercedes Diesel info
JohnMeister.com
|
tmp files
SR9 cam
calculate costs/mile
|
John's Diesel projects:
Jetta TDI, KJ CRD and J10s
john's vehicles
|
BibleTech
MeisterTech
JohnMeister.com
fotomeister.us
misc BIBLE info
Computer Science
LINUX
|
Bible Summary draft version
email john at johnmeister.com/jeep/sj
Trust Jesus.
Jesus Christ is Lord.
|
|
|
